## How to Build Cell Phone Jammer? DIY

dondon pramis
Inventor
Contact:
Location: Philippines
Posts: 54
Joined: Sun Feb 12, 2017 8:28 am

### How to Build Cell Phone Jammer? DIY

Cell phone jammer is an electronic device that blocks transmission of signals between a cell phone and a base station. By using the same frequency as a mobile handset, the cell phone jammer creates strong interference for communication between the caller and receiver. It is efficient in blocking transmission of signals from networks including UMTS, 3G, CDMA, GSM and PHS.

Mobile phones operate at different frequency bands in different countries. For Canada the 1900 MHz band is the primary band, particularly for urban areas. 850 MHz is used as a backup in rural areas. USA uses 850 and 1900 MHz bands, depending on the area. Europeans tend to use the GSM 900 and 1800 bands as standard. Middle East, Africa, Asia and Oceania also use these frequency bands. In Russia and some other countries, local carriers have licenses for 450 MHz frequency to provide CDMA coverage.
Mobile-Jammer-Circuit-Diagram.png (55.66 KiB) Viewed 427 times
The use of different frequencies makes it difficult to have a jammer for all frequencies. However the below mentioned formula can be used to calculate the required values.
F= 1/ (2*pi*sqrt (L1*C1))
Depending on the frequencies you need to block, the values of inductor (L1) and capacitor (C1) can be altered.

For example, if mobile phones at your area work at 450 MHz, you need to generate 450 MHz with some noise to act as the blocking signal. Now the cell phone receiver will not be able to understand, which signal to receive. We have successfully blocked cell phone signals.

Here, 450MHz is the tuning frequency. Cell phone jammers for other frequency ranges are designed similarly. However, the signal range is very weak. Thus, this circuit works only for a range of 100 m.

For any jammer circuit, it’s essential to have three important sub circuits.

1. RF amplifier
2. Voltage Controlled Oscillator
3. Tuning circuit

These 3 circuits, when combined together form an efficient cell phone jammer circuit.

RF amplifier circuit comprises of the transistor Q1, capacitors C4, C5 and resistor R1. This RF circuit amplifies the signal generated by the tuned circuit. The amplified signal is given to the antenna through capacitor C6. It blocks DC and allows only the AC component of the signal to be transmitted.
When transistor Q1 is turned ON, the tuned circuit at the collector turns ON. The tuned circuit consists of capacitor C1 and inductor L1. This acts as an oscillator with zero resistance. It produces very high frequency with minimum damping.

When the circuit is ON, voltage is stored in the capacitor. Once the capacitor is completely charged, it allows charge to flow through the inductor. When current flows through the inductor, it stores magnetic energy corresponding to the voltage across the capacitor. At a certain point, the inductor reaches its maximum and the charge or voltage across the capacitor turns to zero.

Now the magnetic charge through the inductor decreases and the current charges the capacitor in opposite or reverse polarity. The process repeats and after a while, inductor charges the capacitor and becomes zero.

This process runs till internal resistance is generated and the oscillations stop. RF amplifier feed is given through capacitor C5 to the collector terminal before C6. The capacitors C2 and C3 generate pulses in random fashion (noise) at the frequency generated by the tuned circuit.

The RF amplifier boosts the frequency generated by the tuned circuit. The frequency generated by the tuned circuit and the noise signal generated by the capacitors C2 and C3 is combined, amplified and transmitted.

Resistor R2 = Base Biasing
Capacitor C1 = Frequency Generation
Capacitor C2 = Feedback
Capacitor C3 = Feedback
Capacitor C4 = Noise Reduction
Capacitor C5 = Coupling
Capacitor C6 = Coupling
Capacitor C7 = Decoupling
Transistor Q1 = Amplification
Inductor L1 = Frequency Generation

Note
This circuit can block signals only within a 100 meter radius. Usage of this type of circuits is banned and illegal in most countries. This circuit is also used in TV transmission and remote controlled toys.

If the circuit is not working properly, try increasing resistor and capacitors values in the circuit. Use the formula
F= 1/ (2*pi*sqrt (L*C)).
Power supply for the circuit should not exceed 3 Volts.

The cell phone jammer is ban in several countries. Keeping in with those regulations, we might not be able to help you out with the exact values.